BS 3S 500-1996 Procedure for Inspection, testing and acceptance of steel sheet and strip
|
ID： |
D45AF17D270C4AA6B9AC6FC050707385 |
|
文件大小(MB)： |
0.23 |
|
页数： |
26 |
|
文件格式： |
|
|
日期： |
2010-10-4 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD AEROSPACE SERIES BS 3S 500:,1996,Incorporating,Amendment No. 1,Procedure for,Inspection, testing and,acceptance of steel,sheet and strip,ICS 49.025.10,Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:09:54 GMT 2006, Uncontrolled Copy, (c) BSI,BS 3S 500:1996,This British Standard, having,been prepared under the,direction of the Engineering,Sector Board, was published,under the authority of the,Standards Board and comes,into effect on,15 June 1996,. BSI 06-1999,First published April 1956,Second edition August 1969,Third edition June 1996,The following BSI references,relate to the work on this,standard:,Committee reference ACE/61,Draft for comment 92/77503 DC,ISBN 0 580 25484 4,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted to Technical,Committee ACE/61, Inspection and testing requirements for aerospace,metallic materials, upon which the following bodies were represented:,Aluminium Federation,British Forging Industry Association,British Investment Casting Trade Association,British Iron and Steel Producers’ Association,Copper Development Association,Light Metal Founders’ Association,Ministry of Defence,Society of British Aerospace Companies,Amendments issued since publication,Amd. No. Date Comments,9327 February 1997 Indicated by a sideline in the margin,Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:09:54 GMT 2006, Uncontrolled Copy, (c) BSI,BS 3S 500:1996,. BSI 06-1999 i,Contents,Page,Committees responsible Inside front cover,Foreword iii,Section 1. General requirements,1.1 Scope 1,1.2 General 1,1.3 References 1,1.4 Definitions 1,1.5 Information to be supplied by the purchaser 1,1.6 Chemical composition 2,1.7 Manufacture 2,1.8 Temporary identification up to the cast approval stage 2,1.9 Surface dressing of slabs and intermediate products 2,1.10 Surface inspection of slabs and intermediate products 2,1.11 Freedom from defects 2,1.12 Sulfur printing and/or deep etching tests 2,1.13 Cleanness 2,1.14 Ultrasonic inspection 2,1.15 Heat treatment 3,1.16 Surface finish 3,1.17 Mechanical properties 3,1.18 Selection and preparation of mechanical test samples 3,1.19 Tensile test 3,1.20 Bend test 3,1.21 Hardness test 3,1.22 Creep and creep rapture test 4,1.23 Examination for decarburization 4,1.24 Retest procedure 4,1.25 Dimensions and tolerances 7,1.26 Maintenance of identity 9,1.27 Final marking 9,1.28 Certification 9,Section 2. Sheet and strip delivered in the normalized or,softened condition for use without further heat treatment,(excluding austenitic steel),2.1 General 11,2.2 Condition 11,2.3 Tensile test 11,2.4 Bend test 11,2.5 Hardness test 11,2.6 Retests 11,Section 3. Sheet and strip delivered in the softened condition,for use in the hardened and tempered condition,3.1 General 12,3.2 Condition 12,3.3 Tensile test 12,3.4 Bend test 12,3.5 Hardness test 12,3.6 Decarburization 12,3.7 Retests 12,Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:09:54 GMT 2006, Uncontrolled Copy, (c) BSI,BS 3S 500:1996,ii . BSI 06-1999,Page,Section 4. Sheet and strip delivered in the hardened and,tempered condition,4.1 General 13,4.2 Condition 13,4.3 Hardness test 13,4.4 Tensile test 13,4.5 Bend test 13,4.6 Decarburization 13,4.7 Retests 13,Section 5. Not allocated.,Section 6. Corrosion and heat resisting austenitic steel,sheet and strip (high temperature properties not verified),6.1 General 15,6.2 Condition 15,6.3 Tensile test 15,6.4 Bend test 15,6.5 Hardness test 15,6.6 Intercrystalline corrosion test 15,6.7 Retests 15,Section 7. Precipitation hardening steel sheet and strip,7.1 General 16,7.2 Condition 16,7.3 Tensile test 16,7.4 Bend test 16,7.5 Hardness test 16,7.6 Retests 16,Section 8. Finally heat treated parts (made from sheet and strip,delivered in other than the finally heat treated condition),8.1 General 17,8.2 Condition 17,8.3 Selection of mechanical test samples 17,8.4 Mechanical properties 17,8.5 Retests 17,Section 9. Modified requirements for the acceptance of small,quantities of steel,9.1 General 18,9.2 Micro-cleanness assessment 18,9.3 Other tests 18,9.4 Certification 18,Figure 1 — Edge bow 10,Table 1 — Orientation of test pieces 3,Table 2 — Tolerances on thickness of hot-rolled steel,sheet and strip (excluding mild steel) 5,Table 3 — Tolerances on thickness of cold-rolled steel,sheet and strip (excluding mild steel) 6,Table 4 — Tolerances on width of rotary-sheared material 7,Table 5 — Tolerances on width and length of guillotine-sheared material 7,Table 6 — Tolerances on thickness of hot-rolle……
……